- 您现在的位置：买卖IC网 > Sheet目录368 > W9412G6IH-5 (Winbond Electronics)IC DDR-400 SDRAM 128MB 66TSSOPII
W9412G6IH
1) READA ≥ t RAS (min) - (BL/2) x t CK
Internal precharge operation begins after BL/2 cycle from Read with Auto-precharge command.
2) t RCD(min) ≤ READA < t RAS(min) - (BL/2) x t CK
Data can be read with shortest latency, but the internal Precharge operation does not begin until
after t RAS (min) has completed.
This command must not be interrupted by any other command.
7.2.8
Mode Register Set Command
( RAS = “L”, CAS = “L”, WE = “L”, BA0 = “L”, BA1 = “L”, A0 to A11 = Register Data)
The Mode Register Set command programs the values of CAS Latency, Addressing Mode, Burst
Length and DLL reset in the Mode Register. The default values in the Mode Register after power-
up are undefined, therefore this command must be issued during the power-up sequence. Also,
this command can be issued while all banks are in the idle state. Refer to the table for specific
codes.
7.2.9
Extended Mode Register Set Command
( RAS = “L”, CAS = “L”, WE = “L”, BA0 = “H”, BA1 = “L”, A0 to A11 = Register data)
The Extended Mode Register Set command can be implemented as needed for function
extensions to the standard (SDR-SDRAM). Currently the only available mode in EMRS is DLL
enable/disable, decoded by A0. The default value of the extended mode register is not defined;
therefore this command must be issued during the power-up sequence for enabling DLL. Refer to
the table for specific codes.
7.2.10 No-Operation Command
( RAS = “H”, CAS = “H”, WE = “H”)
The No-Operation command simply performs no operation (same command as Device Deselect).
7.2.11 Burst Read Stop Command
( RAS = “H”, CAS = “H”, WE = “L”)
The Burst stop command is used to stop the burst operation. This command is only valid during a
Burst Read operation.
7.2.12 Device Deselect Command
( CS = “H”)
The Device Deselect command disables the command decoder so that the RAS , CAS ,
WE and Address inputs are ignored. This command is similar to the No-Operation command.
7.2.13 Auto Refresh Command
( RAS = “L”, CAS = “L”, WE = “H”, CKE = “H”, BA0, BA1, A0 to A11 = Don’t Care)
AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous to CAS–
BEFORE–RAS (CBR) refresh in previous DRAM types. This command is non persistent, so it
must be issued each time a refresh is required.
The refresh addressing is generated by the internal refresh controller. This makes the address
bits ”Don’t Care” during an AUTO REFRESH command. The DDR SDRAM requires AUTO RE-
Publication Release Date: Sep. 16, 2009
- 11 -
Revision A06
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
W9412G6JH-5I
IC DDR SDRAM 128MBIT 66TSOPII
W9425G6EH-5
IC DDR-400 SDRAM 256MB 66TSSOPII
W9425G6JH-5I
IC DDR SDRAM 256MBIT 66TSOPII
W947D2HBJX5E
IC LPDDR SDRAM 128MBIT 90VFBGA
W948D2FBJX5E
IC LPDDR SDRAM 256MBIT 90VFBGA
W949D2CBJX5E
IC LPDDR SDRAM 512MBIT 90VFBGA
W971GG6JB25I
IC DDR2 SDRAM 1GBIT 84WBGA
W971GG8JB-25
IC DDR2 SDRAM 1GBIT 60WBGA
相关代理商/技术参数
W9412G6JH
制造商:WINBOND 制造商全称:Winbond 功能描述:2M ? 4 BANKS ? 16 BITS DDR SDRAM
W9412G6JH-4
制造商:Winbond Electronics Corp 功能描述:8*16B DDR1 制造商:Winbond Electronics Corp 功能描述:IC DDR SDRAM 128M 250MHZ 66TSOP
W9412G6JH-5
制造商:Winbond Electronics Corp 功能描述:DRAM Chip DDR SDRAM 128M-Bit 8Mx16 2.5V 66-Pin TSOP 制造商:Winbond Electronics Corp 功能描述:128M BIT DDR1
W9412G6JH-5I
功能描述:IC DDR SDRAM 128MBIT 66TSOPII RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:72 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步 存储容量:4.5M（256K x 18） 速度:133MHz 接口:并联 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x20） 包装:托盘
W9412G6JH-5TR
制造商:Winbond Electronics Corp 功能描述:128M DDR SDRAM X16 200MHZ, 65N
W942
制造商:Performance Tool 功能描述:6 Piece Hook and Pick Set 制造商:PERFORMANCE TOOLS 功能描述:6 PC HOOK AND PICK SET
W942508BH
制造商:未知厂家 制造商全称:未知厂家 功能描述:DRAM
W942508CH
制造商:WINBOND 制造商全称:Winbond 功能描述:8M x 4 BANKS x 8 BIT DDR SDRAM